| PVC地板施工难点 |
| 添加时间：2019/4/29 14:48:06 浏览次数： |
| 自流平：自流平浆料倾倒入地坪，任其像水一样流平开来进行自动找平，必须使用专用齿口自流平子母刮板加以来回横向、竖向疏导。在自流平初凝前须穿钉鞋走入自流平地面，用专用放气滚筒滚扎地面以排除因混合时带入的空气，避免气泡，麻面及接口高差。养护1—2天即可铺设。 Self-leveling: Self-leveling slurry is dumped into the floor and left to leveling like water. Special bianpinqi.37ix.com.cndiaoke.37ix.com.cnshidiaodx.37ix.com.cnshidiaofx.37ix.com.cnself-leveling mother scraper with toothed mouth must be used to guide it back and forth horizontally and vertically. Before feiqicc.37ix.com.cnfeiqicl.37ix.com.cnself-leveling and initial solidification, nail shoes should be worn into the self-leveling ground, and special venting drum should be used to roll the ground to remove air brought in by mixing, so as to avoid air bubbles, hemp surface and interface height difference. Maintenance 1 - 2 days can be laid. PVC卷材地板平整度：PVC地板正确的存放方法为竖直存放，不正确的储存方法会导致PVC地板铺贴时形成波浪型，且容易使PVC地板边部损伤，影响安装效果。把切割好的PVC地板平放在地面上，仔细检查PVC地板表面，防止出现质量问题。PVC地板与PVC地板之间不应预留任何空间。铺贴完一个空间，胶水未完全干固前，再用大铁磙推压地面，使已贴好的地板更加平整，或用沙袋压实。 PVC coil floor smoothness: The correct storage method of PVC floor is vertical storage, incorrect storage method will lead to the formation of wave shape when PVC floor is laid, and easy to damage the edge of PVC floor, affecting the installation effect. Place the cut PVC floor flat on the floor and carefully check the surface of the PVC floor to prevent quality problems. No space should be reserved between the PVC floor and the PVC floor. After a space is paved, before the glue is not completely dry, the floor is pressed with a large iron pad to make the laminated floor more flat or compacted with sand bags. PVC地板热力焊接：热力焊接是连接PVC地板接缝的最佳方法。热力焊接应在铺贴PVC地板工作完成24小时后进行。用专业开槽刀或专业自动开槽机在地板接缝处开出“U”型焊槽。槽的深度约为地材的三分之二，但不可超过2mm。用专业焊机把地材专用焊线焊接在“U”型槽内。待焊条温度略降时，用专用铲刀把焊线剩余凸起部分铲掉三分之二，当焊线完全冷却后，再用铲刀把焊线剩余凸起部分完全铲掉。焊线一定要分两次铲除 _PVC floor thermal welding: thermal welding is the best way to connect the joints of PVC floor. Thermal welding should be carried out 24 hours after the work of laying PVC floor. Use professional slotting knife or professional automatic slotting machine to open "U" type weld slot at floor joint. The depth of the trough is about two-thirds of the ground material, but not more than 2 mm. Special welding wires for floor materials are welded in "U" grooves with professional welding machines. When the electrode temperature drops slightly, two-thirds of the remaining protruding part of the welding line is removed with a special spatula. When the welding line is completely cooled, the remaining protruding part of the welding line is completely removed with a spatula. Welding wire must be eradicated twice |
| 上一页 怎么去除Pvc地板的气味 |
| 下一页 如何选用合适的pvc塑胶地板 |
Copyright © 技术支持：遨游网络